Comments on: Yes! http://openservodrive.com/yes/ Cutting edge without Bleeding edge Thu, 15 May 2025 12:21:32 +0000 hourly 1 http://wordpress.org/?v=4.1.12 By: lubchi http://openservodrive.com/yes/#comment-2755 Tue, 10 Mar 2015 21:42:24 +0000 http://openservodrive.com/?p=1423#comment-2755 Sorry for posting relatively the same twice. Internet problems.

]]> By: lubchi http://openservodrive.com/yes/#comment-2754 Tue, 10 Mar 2015 20:59:39 +0000 http://openservodrive.com/?p=1423#comment-2754 Hi,

I’ve played some time with it. Thank you, Tero. It was an 1 KW servo motor with ~1 KW, 1000 rpm, resp. 10 Nm, the DC bus Voltage was 49,5 V. It’s a 10 kg motor. The servo is like 20 grams. Achieved speed – 320 rpm (Rated voltage of the motor ~189 V!!!)
The next try – a real client with a self developed linear motor. The guys there have tried it (unfortunately) with 100 V power supply. Before give it for testing, I’ve attached a 100 W, 10 Ohm brake resistor to the system. Fortunately they had a current limit adjusted to 3 A – the drive still works.
Great!
Is this pinout the valid one for serial production: http://granitedevices.com/wiki/IONI_connector_pinout ?

Wish all of you same good emotions with the first ones of the EONI!

greets Lubchi

]]> By: Tero http://openservodrive.com/yes/#comment-2750 Tue, 10 Mar 2015 11:30:23 +0000 http://openservodrive.com/?p=1423#comment-2750 Good to hear that :)

Full documentation is in the works. Also specs page is already there:
http://granitedevices.com/wiki/IONI_specifications

]]> By: lubchi http://openservodrive.com/yes/#comment-2747 Mon, 09 Mar 2015 13:10:46 +0000 http://openservodrive.com/?p=1423#comment-2747 Hi. I’ve played with it a little bit. Also with a 1 KW motor and a 1.2 kW PSU. Great. There are some end customers already too. Which is the state of the documentation? Is this pinout http://granitedevices.com/wiki/IONI_connector_pinout the right one?

]]> By: Phillip van Rensburg http://openservodrive.com/yes/#comment-2743 Sun, 08 Mar 2015 05:49:39 +0000 http://openservodrive.com/?p=1423#comment-2743 Looking great Tero,
Cannot wait to start with the direct drive force feedback wheel using these :)

Great work, will sent you an email!

Cheers,
Phillip Metso

]]> By: Tero http://openservodrive.com/yes/#comment-2740 Fri, 06 Mar 2015 22:27:53 +0000 http://openservodrive.com/?p=1423#comment-2740 Yes, we have them too.

]]> By: João http://openservodrive.com/yes/#comment-2739 Fri, 06 Mar 2015 21:06:38 +0000 http://openservodrive.com/?p=1423#comment-2739 Can’t wait to test it :)

The IONICUBE was in production to?

João

]]> By: walter http://openservodrive.com/yes/#comment-2738 Fri, 06 Mar 2015 19:40:38 +0000 http://openservodrive.com/?p=1423#comment-2738 Great work, congratulations!

]]>